企业在青岛FAG轴承店买了轴承之后，对于FAG轴承的安装却并不是非常清楚，这是因为企业内部没有专业的安装人员造成的，因此企业如果购买了FAG轴承的话，可以让FAG轴承的生产厂家派一名专业的安装人员来帮你进行安装，这样就省去了很多麻烦。刚好也可以让员工进行学习安装，那么在安装FAG轴承的时候，应该注意一些什么问题呢?
Enterprises buy back FAG bearings, the FAG bearing installation is not very clear, this is because there is no professional installation personnel inside the enterprise, so if the enterprise purchased FAG bearings, can let the FAG bearing manufacturers send a professional installation personnel to help you install, so save I went to a lot of trouble. Just can let the staff learn to install, so when installing FAG bearings, what problems should be noted?
首先，在安装FAG轴承的时候，千万不要直接用锤子或者是其他的一些重物，捶打FAG轴承的端面以及非受力面，这样会造成FAG轴承部分损伤的，在安装FAG轴承的时候，可以用压块或者是套筒，也可以用一些特殊的工具使FAG轴承的受力面均匀一些，这样就不会造成FAG轴承单方面的受力了。
First of all, when installing FAG bearings, do not directly hammer or some other heavy objects, hammering the end face of FAG bearings and non-stressed surface, this will cause FAG bearings partial damage, in the installation of FAG bearings, you can use the pressure block or sleeve, also can use some special tools to make FAG bearings. The force surface is even, so that the FAG bearing will not be subjected to unilateral force.
其次，在安装的表面非常好涂上一层润滑油，这样就能使安装更加顺利。同时，当遇到过盈比较大的时候，就需要把FAG轴承放在矿物油当中进行加热，当温度达到90-100度的时候，就可以将FAG轴承拿出来进行安装了。
Secondly, it is very good to put a layer of lubricant on the surface of the installation, so that the installation can be more smoothly. At the same time, when the interference is relatively large, FAG bearings need to be placed in mineral oil for heating, when the temperature reaches 90-100 degrees, FAG bearings can be taken out for installation.
再次，如果是拆卸FAG轴承的话，也是需要使用一些专门的额拆卸工具，且不可强拆，如果遇到困难的话，也可以使用热油浇洒在FAG轴承的圈内，这样在热胀冷缩的情况之下，FAG轴承就比较容易脱落下来。
Thirdly, if it is to remove FAG bearings, it is also necessary to use some special forehead removal tools, and can not be forced to remove, if there are difficulties, you can also use hot oil sprinkled in the FAG bearing ring, so in the case of hot expansion and cold contraction, FAG bearings are easier to fall off.
非常后，有很多人说在安装FAG轴承的时候，不知道FAG轴承是不是应该先清洗一下，然后在进行安装。其实在安装FAG轴承的时候，是应该先进行清洗的，因为在FAG轴承的表面有一层防锈油，只有使用清洗剂把这层防锈油洗掉了，才能涂上润滑脂，这样在安装FAG轴承就是比较好的。
Very late, many people said that when installing FAG bearings, do not know whether FAG bearings should be cleaned first, and then installed. In fact, when installing FAG bearings, it should be cleaned first, because there is a layer of anti-rust oil on the surface of FAG bearings, only the use of cleaning agent to wash this layer of anti-rust oil, can be coated with grease, so in the installation of FAG bearings is better.